Mold remediation referrals for West Palm Beach & nearby townsCall: (561) 680-4689
(561) 680-4689

Mold in Walls in Lighthouse Point, FL

westpalmbeachmoldremoval.net

Block walls, sliders, plumbing and AC condensation all send water into wall cavities in Lighthouse Point, and the mold follows quietly.

Baseboards swelling in your Lighthouse Point house?
Call now to be connected with a local mold remediation company in Lighthouse Point.
(561) 680-4689

If you suspect mold inside a wall, stop the water source first and keep the area ventilated, then have a local company check the cavity. Removal usually means cutting out the affected drywall and drying what remains. Call the number on this page to be connected with a local mold company in Lighthouse Point.

Inspection opening showing mold inside a wall cavity, mold in walls in Lighthouse Point, FL

When a small stain is not small

A coin-sized stain on a wall may be the visible edge of a much larger wet area. Water travels along studs and pools at the bottom plate, so the damage behind the finish can run well past the mark. If a stain is near a plumbing wall, a window or a sliding door, treat it as a lead and not as a cosmetic issue.

Common sources and where they show up

SourceWhere it usually shows
Window or slider seepageBelow the sill, floor edge
Shower or tub valve leakWall behind and beside the tub
Stucco cracksExterior-facing room walls
Condensate overflowWall near the air handler

The pattern of wet spots on a wall often gives away where the water is entering, which is why readings come before repairs.

Salt air and wind-driven rain along the coast push water into stucco cracks and window frames, and humid sea air keeps wall cavities from drying out between storms.

Call now to be connected with a local mold remediation company in Lighthouse Point.
(561) 680-4689
Stained and peeling wall near an exterior door, mold in walls in Lighthouse Point, FL

Why two quotes can look so different

One company may price only the removal, while another includes drying equipment, containment and repair of the opened wall. Before you compare, check what each quote covers. A lower figure that leaves you hiring a second contractor to close up the wall may not be the better deal.

Permits, flood maps and licenses in Lighthouse Point

Check the company's state mold assessor or remediator license on DBPR's search; Florida issues both license types.

Expect two separate companies if you want both an assessment and remediation: state rules keep the assessor and the remediator apart on the same structure for 12 months.

Rebuild work after the mold comes out, such as new drywall or framing, may need a permit; the Lighthouse Point Building Department is the office for Lighthouse Point addresses.

If storm water was involved, your insurer and FEMA's flood maps can tell you how the address is zoned.

Calls from Lighthouse Point are often matched with companies that also cover Pompano Beach, Deerfield Beach and Coconut Creek.

Removal, drying and the rebuild

Affected drywall and insulation are cut out and bagged, framing is cleaned or treated as needed, and fans or dehumidifiers dry the cavity. Many companies stop there and leave the closing and painting to a general contractor, so confirm who handles the rebuild before you sign.

Make the repair last

The wall is only as dry as its source. Once the company has removed the damage, make sure the pipe, seal or stucco crack that caused it has been repaired, and keep an eye on the area for a few weeks. If the smell or stain returns in Lighthouse Point, call again right away.

Mold in Walls questions in Lighthouse Point

What is a thermal camera used for in a wall check?
It shows temperature differences that can point to damp areas. It does not detect mold itself, so it guides where to take moisture readings or open the wall.
Can I just clean the wall and paint over it?
Not if the growth is inside. EPA says to fix the moisture first and that porous materials that stay moldy usually have to be removed.
How long can drywall stay wet before mold starts?
EPA advises drying wet materials within 24 to 48 hours. After that, growth becomes more likely, especially in a warm, humid house.
Who fixes the leak that caused the mold?
Usually a plumber, window installer, roofer or stucco contractor. The mold company removes the damage but does not repair the source.

More mold services in Lighthouse Point

Mold in Walls nearby

Call now to be connected with a local mold remediation company in Lighthouse Point.
(561) 680-4689

Last updated:

☎ Call (561) 680-4689