In South Florida the air conditioner runs most of the year, and that makes it one of the likeliest places for moisture and mold to build up. A South Florida price guide lists AC and duct mold cleaning at $3,000 to $10,000 per job, so it pays to know the signs early.
Why AC systems collect mold here
An air conditioner removes humidity as it cools. That moisture collects on the coil, drips into a pan and leaves through a condensate drain line. In a climate where the system works hard for most of the year, the coil is wet for long stretches, the pan can hold water and the line can clog with algae and debris. Many homes keep the air handler in a closet, garage or attic, so a small leak can go unnoticed for a long time. Add a hot attic and warm, humid indoor air and you have the conditions mold likes.
EPA states that the key to mold control is moisture control, and that advice applies to your air conditioning as much as to a roof. If you suspect a problem, the number on this page connects you with an independent local mold company in West Palm Beach. We are a referral service, not an HVAC or mold company.
Signs to look for
- A musty or earthy smell when the system starts, or one that gets stronger near a vent.
- Visible dark or fuzzy growth on vent covers, registers or around the louvers.
- Water stains or damp drywall around the air handler closet, on the ceiling below an attic unit, or on the floor around the pad.
- Condensation or sweating on ducts, vents or the ceiling near a register.
- A drain pan with standing water, slime or rust.
- Rooms that never quite cool, or a unit that runs constantly.
- Dust or dark particles blowing from the vents when the fan starts.
Any one of these can have a simple cause. A smell, for instance, may be from the coil or the drain, not from mold in the duct walls. That is why a proper look matters before anyone sells you a full replacement. If you have health concerns, talk with your doctor. The CDC states that exposure to damp and moldy environments may cause a variety of health effects, or none at all.
The usual causes
- Clogged condensate drain. The most common cause. Water backs up into the pan, overflows and soaks the area around the unit.
- Dirty coil or filter. Restricted airflow can let the coil get colder and wetter and gather debris.
- Leaky or uninsulated ducts. In a hot attic, cold ducts sweat when insulation is torn, wet or missing. That moisture soaks insulation and ceiling drywall.
- An oversized system. A unit that cools too fast shuts off before it removes much humidity, which leaves indoor air damp. EPA advises keeping indoor relative humidity below 60 percent, ideally between 30 and 50 percent, and the CDC says no higher than 50 percent.
- Storm or flood water. Water reaching the unit or ductwork can leave moisture inside. See mold after a hurricane or flood before you restart a wet system.
- Roof leaks above attic equipment. Water drips onto the unit or insulated ducts.
What you can safely do yourself
- Replace the filter on schedule. A clogged filter is a common contributor.
- Check that the condensate line is draining and the pan is dry. Many systems have a cleanout or a float switch.
- Wipe visible surface growth on hard vent covers with detergent and water, and dry them. EPA says that for an area under about 10 square feet you can usually handle cleanup yourself, but that applies to a small, accessible patch, not to the inside of a duct.
- Run a hygrometer to see your humidity. A number above 60 percent most of the time is a clue.
- Do not spray bleach into vents. EPA states that biocides such as chlorine bleach are not recommended as a routine practice during mold cleanup.
An HVAC contractor, not a mold company, is the right call for drain repairs, refrigerant, coil work and replacing equipment.
What professional cleanup involves
When growth is inside the system, or when the surrounding drywall and insulation are affected, the job is bigger. A typical sequence looks like this.
- An assessment of the air handler, coil, drain pan, plenums, ducts and the area around them, usually with a moisture meter.
- Containment of the work area so spores do not travel into living space.
- Removal of affected porous materials, such as damaged flexible duct, duct board, wet insulation and drywall.
- Cleaning of hard components with HEPA vacuuming and approved methods.
- Repair of the moisture source: drain, insulation, leaks or humidity control.
- Verification that the work is complete.
Damaged flexible duct and insulated duct board are often replaced instead of cleaned, which helps explain why a South Florida price guide lists AC and duct mold cleaning at $3,000 to $10,000 per job, well above a typical single room. The same guide lists attic mold at $1,000 to $7,000. Our full cost guide places the numbers side by side, and the AC and duct mold removal page covers the service itself. When the unit sits in the attic, attic mold removal often comes into the same job.
Who does what
This is where people get confused. An HVAC contractor repairs and replaces equipment. In Florida, a mold assessor and a mold remediator hold separate state licenses issued through DBPR, and only individuals hold them. If someone says mold needs to be cleaned from your ducts, ask who holds the state mold license and look it up on DBPR's search, as our mold license guide explains. If an assessor wrote the scope, the 12-month rule means the same company generally cannot remediate. Note also that "duct cleaning" is not the same service as mold remediation, and a company offering only a vent vacuum is not addressing a moisture source.
Common South Florida mistakes
- Turning the thermostat way down to fight humidity. Colder settings can make ducts sweat more and do not fix a damp house.
- Closing vents in unused rooms. It can unbalance the system and create cold spots.
- Ignoring a small drip at the air handler because it is in a closet.
- Replacing the system without fixing the drain, the insulation or the leak that caused the problem.
- Buying a "treatment" or fogging service with no inspection first.
For long-term habits, see our guide on keeping mold away in a humid climate. If you rent a home or live in a condo, tell the landlord or association in writing; our guide to condos and rentals covers responsibility. We cover Palm Beach County towns and nearby Martin and Broward towns, listed on the service areas page.
A quick routine for owners with a mold-prone unit
Once a year, before the wet season, check the air handler closet, look at the drain line cleanout and the pan, and scan the attic for stained insulation or dripping ducts. Make sure bathroom fans vent outdoors. If your system is older, ask your HVAC contractor about the drain, the insulation and the sizing of the equipment. A few minutes of attention costs far less than the ranges quoted above, and it gives you a baseline to compare against if a smell shows up later. Keep a simple log of filter changes and drain checks, so you can show a pattern if a warranty or insurance question comes up. For related problems, see mold smell with nothing visible.
When to call a professional instead of an HVAC tech
Call an HVAC contractor first when the problem is mechanical: a leaking line, a frozen coil, weak cooling or a failed float switch. Call a local mold company when growth is visible on drywall, insulation or duct material, or when a musty smell persists after the drain and filter are fixed. Many jobs need both, in sequence: the mold work removes affected material, then the HVAC contractor repairs the system so the moisture does not return. Ask each to coordinate, and ask who will pull any permit for equipment work.
Frequently asked questions
How do I know if there is mold in my air conditioner?
How much does AC mold removal cost in South Florida?
Can I clean mold from my ducts myself?
What humidity should I keep in my house?
Sources
- EPA: A Brief Guide to Mold, Moisture and Your Home
- EPA: Mold Cleanup in Your Home
- CDC: About Mold and Your Health
- Mold Remediation Cost in South Florida (Advanta Clean price guide)
- Florida DBPR: Mold-Related Services FAQs
- Florida DBPR: Mold-Related Services license search
- Florida Department of Health: Mold
Last updated: